GKTECH
M14 Super Adjustable Inner Tie Rod
What is a Backorder?
Q: What is backorder?
When a product is on backorder, it means that we have sold out and we are opening a back order due to popular demand. This is essentially a queue, when new stock arrives from production, we’ll send your order.Q: Will items in my order that are in stock be shipped out first?
We will send your order altogether once your backorder item is ready! You may wish to place separate orders if you want an item before the other is due back in stock.Free Shipping on orders over $250
Checking Dispatch Times...
Order and earn 5% back in reward points
That's 225 for this item
The final product as shown in the photos compared to some popular alternate tie rods shows just how much adjustment our tie rod has.
- Short tie rod adjustable from 66mm minimum length through to 250mm(183mm) of adjustment
- Long tie rod adjustable from 175mm minimum length through to 340mm(175mm) of adjustment
- M14 in size for increased strength over M12 setups
- Rod is manufactured from HRC 25-28 Steel with PTFE (Teflon) lined maintenance free bearing
- 50 degrees range of motion (25 degrees misalignment)
- Sold individually
FAQs
How hard are these to install?Remove your old tie rods, measure where these need to be cut in length and install them. It's a very self explanatory install and shouldn't take longer than 30 minutes.
Will this fit my car?
If your car is listed above then the tie rods will fit however they may also fit other setups not listed but we can't be sure.
Do I need a wheel alignment after installing these?
Unless you get the length spot on perfect, you will need a wheel alignment after installation.
What thread pitch is the rack end?
The M14 Inner tie rod is M16X1 on the end that goes into the steering rack and M14x1.5 on the end that goes into the outer tie rod end.
VEHICLE COMPATIBILITY
NOTE: If you have an S13/180sx, S15 or R32 Skyline and upgrading to the M14 inners, you will need to change the tie rod to an M14 version such as that used on the S14, R33 etc
Nissan
R32 SKYLINE GTRR32 SKYLINE GTS-T
R33 SKYLINE GTR
R33 SKYLINE GTS-T
R34 SKYLINE GT-T
R34 SKYLINE GTR
S13 CA18 180SX
S13 CA18 SILVIA
S13 SR20 180SX
S13 SR20 SILVIA
S14 200SX/SILVIA
S15 200SX/SILVIA
V35 SKYLINE
Z32 300ZX
Z33 350Z
Z34 370Z
Customer Reviews
とても良かったです。
I keep a dozen with me at all times because you can put them on any car. Tons of thread engagement, good ball joints, and they’re black which makes them stealthier
When installing the gktech rcc kit on my s13, i needed longer threads into the tie rod ends to be safe. I checked bolt in rack spacers to see if it would give me the length i needed, but found that compromised oe inner tie rod thread length too much. I needed a solution that addresses both inner and outer thread length.
This long product does exactly that. I used the
gktech bolt in rack spacers and had peace of mind with reasonable thread engagement into the rack, while cutting the outer threads to the exact length i needed to get a ton of thread engagement to the outer tie rods too. Also upgraded to s14 outer tie rod ends (needed with these inners).
Cut with a cutoff wheel
Grind a small 2-4mm chamfer with a bench grinder, with the wheel direction going from thread to center of the rod.
Chase with a thread file if necessary. (Grinding this direction, i didnt need to fix any threads).
Check pics for more tips when pairing with bolt-in rack spacers, i did some extra grinding so my standard 32mm wrench could fit on the outer tie rod. (Not necessary when not using the bolt-in rack spacer)
Great fitment, easy install. I had to cut about a half inch off the end of the long tie rod to fit my car but that was quick and easy too.
Cant say enough good things about gktech. Customer support is top notch, super fast shipping and quality affordable parts. Thanks for everything
